You have finally decided to build a pool in your backyard. During construction, there are many things to look for during progress inspections. For example, you should check the installation of safety covers and gas lines. You also want to check the safety cover and insulation of the pump area. To ensure that the pool construction process runs smoothly, you should schedule inspections ahead of time. This will allow you to plan accordingly, and avoid any unnecessary delays.
Installation of gas lines
There are several benefits to installation of gas lines
during swimming pool construction. Gas appliances typically perform better than
their electric counterparts. Properly calibrating these systems is an important
aspect of the construction process. Otherwise, gas-powered appliances could
result in leaks or compromise the integrity of the piping. The installation
process is complicated and should be performed by a professional plumber. Not
only will this reduce the chances of a leak, but a professional will also be
able to determine the proper flow rates and BTUs of each gas appliance.
Proper installation of gas piping must be conducted before concealment. The copper tracer wire used for gas piping must be no less than #14 AWG. The copper tracer wire must also be inspected and approved. The gas shut-off valve must be installed at the outside perimeter of the structure and at least three feet from the heater. Additionally, swimming pools must have a 125-volt convenience receptacle at the entrance to the pool.
Insulation of pump area
When building a swimming pool, the perimeter surface must be
bonded with at least an eight-AWG solid copper bonding conductor. The bonding
wires must be attached at four points along the perimeter, including the walls
and covers. A solid copper bonding conductor must be placed on top of an
unpaved or paved area at least one foot away from the perimeter of the Swimming Pool Construction.
This will prevent voltage potentials and gradients in the area surrounding the
pump.
If the pool's structure is made of metal, all parts must be
bonded to the concrete. Underwater lighting may contain metal forming shells
and mounting brackets. All metallic parts of the swimming pool structure must
be bonded. Copper tie wires are suitable for bonding conductive metal parts,
but nonconductive materials such as vinyl and fiberglass should be used. Also,
electrical equipment associated with the circulation of water must be bonded.
Installation of safety cover
When installing a safety cover during swimming pool
construction, you should begin by ensuring the material is level over the
entire pool. Also, pay attention to the cutout locations on the cover. Keeping
these locations in mind, you can adjust the straps if necessary. Then, position
the cover over the pool and adjust the straps to adjust the coverage. Depending
on the design of your swimming pool, you may need to adjust the safety cover at
different spots.
Drill two holes a few inches from each corner of the pool.
Then, install two anchors on either side of the center seam. This should ensure
that the cover is centered over the pool and not sag or pull in one direction.
If the cover does not lie flat, make slight adjustments to the anchors,
including adjusting the length of the springs. Once you're satisfied with the
centering of the cover, place it over the pool
Requirements of progress inspections
Depending on the town or county in which you live, you may
need to conduct Special and Progress Inspections during the swimming pool
construction process. A Special Inspection Agency (SIA) is the typical
contractor engaged by permit holders, but you may also be able to perform some
of these inspections yourself. The DOB requires that the temporary fence
surrounding the swimming pool be 36 inches high, and any dogs must be removed
from the site.
If your swimming pool is on a private property, you must
ensure that the water is disposed of properly. You must ensure that the pool
will not interfere with an existing private septic system, nor will it drain
onto adjoining properties. You must also ensure that your swimming pool is
equipped with all the required electrical fixtures. The last inspection must be
performed after the building is ready to be occupied.
Final inspection
Before plastering a swimming pool, the final inspection of
the swimming pool must be completed. The inspector will check the condition of
the pool's tile and grout, as these areas need to be waterproof. He will also
check if the tiles have chips or cracked grout. The inspector will also check
whether the pool has any other safety features, such as a diving board or a
safety net. If the inspector finds problems, he will recommend an appropriate
course of action to resolve the issue.
The inspector will check the condition of the pool's
interior finish for cracks and structural problems. He will note if the pool
needs to be resurfaced and repair the rips in the liner. The inspector will
also check the surrounding variables such as proper drainage. Proper drainage
is essential, as rainwater can overflow onto the ground and cause a pool leak.
It is important to follow regulations for installing new swimming pools in your
area, and a proper inspection can ensure that your Swimming
Pool Inspection meets the standards set by your local authorities.
